International Journal of Machining and Machinability of Materials (IJMMM)

International Journal of Machining and Machinability of Materials

2013 Vol.13 No.2/3

Special Issue on Machining of Aerospace Materials

Guest Editors: Dr. Redouane Zitoune, Dr. Vijayan Krishnaraj and Professor J. Paulo Davim

Editorial

Book Review

Pages Title and author(s)
113-137Chip segmentation behaviour and surface topography in high-speed turning of titanium alloy (Ti-6Al-4V) with eco-friendly water vapour
Raju S. Pawade; D.S.N. Reddy; Ganesh S. Kadam
DOI: 10.1504/IJMMM.2013.053218
138-157Optimisation and tool life study in drilling of titanium (Ti-6Al-4V) alloy
Arumugam Prabukarthi; Vijayan Krishnaraj; Murugan Santhosh; Mouleeswaran Senthilkumar; Redouane Zitoune
DOI: 10.1504/IJMMM.2013.053219
158-173Analysis of coating performances in machining titanium alloys for aerospace applications
M. Nouari; Madalina Calamaz; B. Haddag; Franck Girot
DOI: 10.1504/IJMMM.2013.053220
174-190Evaluation of drilling process in Ti6Al4V using 3D FE simulation
Ozden Isbilir; Elaheh Ghassemieh
DOI: 10.1504/IJMMM.2013.053221
191-202Design optimisation of machining parameters for turning titanium alloys with Taguchi-Grey method
Kosaraju Satyanarayana; Anne Venu Gopal; Popuri Bangaru Babu
DOI: 10.1504/IJMMM.2013.053222
203-214Influence of minimum quantity lubrication on the high speed turning of aerospace material superalloy Inconel 718
D.G. Thakur; B. Ramamoorthy; L. Vijayaraghavan
DOI: 10.1504/IJMMM.2013.053223
215-230Development of semi empirical model for predicting material removal rate during orbital electro discharge machining of Inconel 718
Harshit K. Dave; Keyur P. Desai; Harit K. Raval
DOI: 10.1504/IJMMM.2013.053224
231-252Effects of lubrication modes on part quality during drilling 6061-T6 aluminium alloy
Yasser Zedan; Victor Songmene; Jules Kouam; Jacques Masounave
DOI: 10.1504/IJMMM.2013.053225
253-261Temperature measurement during grinding of metal matrix composites
B. Anand Ronald; L. Vijayaraghavan; R. Krishnamurthy
DOI: 10.1504/IJMMM.2013.053226
262-275An experimental analysis of single pass cutting of aluminium 5083 alloy in different corner angles through WEDM
G. Selvakumar; S. Sarkar; S. Mitra
DOI: 10.1504/IJMMM.2013.053227
276-288Usage of PCD tool in drilling of titanium/graphite hybrid composite laminate
D. Kim; C. Sturtevant; M. Ramulu
DOI: 10.1504/IJMMM.2013.053228
289-310Machinability and surface quality during high speed trimming of multi directional CFRP
Madjid Haddad; Redouane Zitoune; Florent Eyma; Bruno Castanié
DOI: 10.1504/IJMMM.2013.053229
311-330Machining carbon fibre reinforced plastics: lead angle effect
A. Morandeau; H. Chibane; A. Bouchou; R. Serra; D. Bonhoure; R. Leroy
DOI: 10.1504/IJMMM.2013.053230
331-347Effect of edge trimming on failure stress of carbon fibre polymer composites
J. Sheikh-Ahmad; A.H. Shahid
DOI: 10.1504/IJMMM.2013.053231

 

Return to top