Journal cover image

Browse issues

Vol. 57
Vol. 56
Vol. 55
Vol. 54
Vol. 53
Vol. 52
Vol. 51
Vol. 50
Vol. 49
Vol. 48
Vol. 47
Vol. 46
Vol. 45
Vol. 44
Vol. 43
Vol. 42
Vol. 41
Vol. 40
Vol. 39
Vol. 38
Vol. 37
Vol. 36
Vol. 35
Vol. 34
Vol. 33
Vol. 32
Vol. 31
Vol. 30
Vol. 29
Vol. 28
Vol. 27
Vol. 26
Vol. 25
Vol. 24
Vol. 23
Vol. 22
Vol. 21
Vol. 20
Vol. 19
Vol. 18
Vol. 17
Vol. 16
Vol. 15
Vol. 14
Vol. 13
Vol. 12
Vol. 11
Vol. 10
Vol. 9
Vol. 8
Vol. 7
Vol. 6
Vol. 5
Vol. 4
Vol. 3
Vol. 2
Vol. 1

International Journal of Materials and Product Technology

2016 Vol. 52 No. 1/2

Special Issue on Polymers and Moulds Innovations

Guest Editor: Professor António Sérgio Pouzada


PagesTitle and authors
3-16An analysis of Digital ABS as a rapid tooling material for polymer injection moulding
Neri Volpato; Daphene Marques Solis; Carlos Alberto Costa
DOI: 10.1504/IJMPT.2016.073616

17-36Influence of tool surface on wall sliding of polymer melts
G. Zitzenbacher; T. Bayer; Z. Huang
DOI: 10.1504/IJMPT.2016.073617

37-52Mechanical and dimensional characterisation of polypropylene injection moulded parts in epoxy resin/aluminium inserts for rapid tooling
Anderson De Carvalho Fernandes; Adriano Fagali De Souza; Janaina Lisi Leite Howarth
DOI: 10.1504/IJMPT.2016.073618

53-75Thin wall injection-overmoulding of polyamide 6/polypropylene multilayer parts: influence of processing conditions on thermomechanical properties of the layer assembly
Sandra Macedo; Eric Lafranche; Carla I. Martins; Catherine Douchain; Cyril Loux; Patricia Krawczak
DOI: 10.1504/IJMPT.2016.073619

76-95Applying flow simulations in the development process of injection moulded thermoplastic parts
Carlos N. Barbosa; Francisco Carvalho; Julio C. Viana; Markus Franzen; Thomas Baranowski; Ricardo Simoes
DOI: 10.1504/IJMPT.2016.073620

96-117Realising a child's imagination through a child-led product design for both two-dimensional and three-dimensional product
Rafat Madani; Adam Moroz; Emily Baines; Bilal Makled
DOI: 10.1504/IJMPT.2016.073621

118-142Numerical simulation and experimental study on physical mechanism in multiple component moulding
Chao-Tsai Huang; Che-Ping Lin; Shih-Po Sun; Shi-Chang Tseng; Rong-Yeu Chang
DOI: 10.1504/IJMPT.2016.073627

143-161Combination of laser welding with in-mould assembling into a single process
Nelson Oliveira; A.J. Pontes
DOI: 10.1504/IJMPT.2016.073629

162-175Using a glass-fibre reinforced polymer composite in the production of sustainable water storage tanks
Carla L. Simões; M. Vasconcelos; J.P. Nunes; C.A. Bernardo
DOI: 10.1504/IJMPT.2016.073628

176-192Influence of twin-screw configuration on the mechanical and morphological properties of polypropylene-clay composites
Laurens Delva; Kim Ragaert; Klaas Allaer; Antonio Gaspar-Cunha; Joris Degrieck; Ludwig Cardon
DOI: 10.1504/IJMPT.2016.073631

193-211A study on the role of wetting parameters on friction in injection moulding
Gerald R. Berger; Clemens Steffel; Walter Friesenbichler
DOI: 10.1504/IJMPT.2016.073632