2025 Vol.18 No.42025 Vol.18 No.32025 Vol.18 No.1/22024 Vol.17 No.42024 Vol.17 No.2/32024 Vol.17 No.1 Free Access2023 Vol.16 No.62023 Vol.16 No.52023 Vol.16 No.42022 Vol.16 No.2/32022 Vol.16 No.12021 Vol.15 No.5/62020 Vol.15 No.42020 Vol.15 No.32020 Vol.15 No.22020 Vol.15 No.12019 Vol.14 No.62019 Vol.14 No.52019 Vol.14 No.42019 Vol.14 No.32019 Vol.14 No.22019 Vol.14 No.12018 Vol.13 No.62018 Vol.13 No.52018 Vol.13 No.3/42018 Vol.13 No.1/22017 Vol.12 No.5/62017 Vol.12 No.3/42017 Vol.12 No.1/22016 Vol.11 No.62016 Vol.11 No.52016 Vol.11 No.3/42016 Vol.11 No.1/22015 Vol.10 No.5/62015 Vol.10 No.3/42015 Vol.10 No.22015 Vol.10 No.12014 Vol.9 No.62014 Vol.9 No.3/4/52014 Vol.9 No.22014 Vol.9 No.12013 Vol.8 No.62013 Vol.8 No.4/52013 Vol.8 No.32013 Vol.8 No.1/22012 Vol.7 No.62012 Vol.7 No.52012 Vol.7 No.42012 Vol.7 No.2/32012 Vol.7 No.12011 Vol.6 No.62011 Vol.6 No.52011 Vol.6 No.3/42011 Vol.6 No.1/22010 Vol.5 No.62010 Vol.5 No.4/52010 Vol.5 No.2/32010 Vol.5 No.12009 Vol.4 No.5/62009 Vol.4 No.42009 Vol.4 No.32009 Vol.4 No.22009 Vol.4 No.12008 Vol.3 No.62008 Vol.3 No.4/52008 Vol.3 No.2/32008 Vol.3 No.12007 Vol.2 No.3/42007 Vol.2 No.22007 Vol.2 No.12006 Vol.1 No.3/42006 Vol.1 No.22005 Vol.1 No.1

International Journal of Microstructure and Materials Properties (IJMMP)

International Journal of Microstructure and Materials Properties

2006 Vol.1 No.2

Editorial

Pages Title and author(s)
129-138Characterisation of an aluminium engine block
Ruben Torres, Jaime Esparza, Eulogio Velasco, Salvador Garcia-Luna, Rafael Colas
DOI: 10.1504/IJMMP.2006.010621
139-148Effect of pouring temperature on the microstructure and the mechanical properties of low pressure sand cast LM25 (Al-7Si-0.3Mg) alloy
A. Srinivasan, U.T.S. Pillai, B.C. Pai
DOI: 10.1504/IJMMP.2006.010622
149-160Microstructural evolution and phase precipitation on ageing Al-Cu alloy
Rupa Dasgupta, Humaira Meenai, M.S. Yadav
DOI: 10.1504/IJMMP.2006.010623
161-182Residual stress and fatigue strength after transformation hardening and various strain hardening
Janez Grum
DOI: 10.1504/IJMMP.2006.010624
183-196Verification of distortion characteristics in water quenched cylinders by computer simulation
Kyozo Arimoto, Takashi Horino, Fumiaki Ikuta, Chuanrong Jin, Shigeyuki Tamura, Michiharu Narazaki
DOI: 10.1504/IJMMP.2006.010625
197-207Study and modelling of microstructural evolutions and thermomechanical behaviour during the tempering of steel
Yunning Wang, Benoit Appolaire, Sabine Denis, Pierre Archambault, Bernard Dussoubs
DOI: 10.1504/IJMMP.2006.010626
208-218Investigation of as-quenched and tempered commercial steels by Magnetic Barkhausen Noise method
C. Hakan Gur, ibrahim Cam
DOI: 10.1504/IJMMP.2006.010627
219-230Residual stress analysis after laser surface alloying with various powdered materials
Janez Grum, Matjaz Znidarsic
DOI: 10.1504/IJMMP.2006.010628
231-240Improvement of tool life of die-casting tools with duplex treatment
Mirko Sokovic, Peter Panjan, Miha Cekada
DOI: 10.1504/IJMMP.2006.010629
241-257Influence of temperature profile in an annular shaft kiln on calcination
Andrej Senegacnik, Janez Oman, Brane Sirok
DOI: 10.1504/IJMMP.2006.010630

 

Return to top