2026 Vol.28 No.22026 Vol.28 No.12025 Vol.27 No.42025 Vol.27 No.32025 Vol.27 No.22025 Vol.27 No.1 Free Access2024 Vol.26 No.42024 Vol.26 No.32024 Vol.26 No.22024 Vol.26 No.12023 Vol.25 No.3/42023 Vol.25 No.22023 Vol.25 No.12022 Vol.24 No.62022 Vol.24 No.52022 Vol.24 No.3/42022 Vol.24 No.1/22021 Vol.23 No.5/62021 Vol.23 No.42021 Vol.23 No.32021 Vol.23 No.22021 Vol.23 No.12020 Vol.22 No.62020 Vol.22 No.52020 Vol.22 No.3/42020 Vol.22 No.22020 Vol.22 No.12019 Vol.21 No.5/62019 Vol.21 No.42019 Vol.21 No.32019 Vol.21 No.1/22018 Vol.20 No.62018 Vol.20 No.52018 Vol.20 No.42018 Vol.20 No.32018 Vol.20 No.22018 Vol.20 No.12017 Vol.19 No.62017 Vol.19 No.52017 Vol.19 No.42017 Vol.19 No.32017 Vol.19 No.22017 Vol.19 No.12016 Vol.18 No.5/62016 Vol.18 No.42016 Vol.18 No.32016 Vol.18 No.1/22015 Vol.17 No.62015 Vol.17 No.52015 Vol.17 No.3/42015 Vol.17 No.22015 Vol.17 No.12014 Vol.16 No.3/42014 Vol.16 No.2 Open Access2014 Vol.16 No.12014 Vol.15 No.3/42014 Vol.15 No.1/22013 Vol.14 No.42013 Vol.14 No.32013 Vol.14 No.22013 Vol.14 No.12013 Vol.13 No.42013 Vol.13 No.2/32013 Vol.13 No.12012 Vol.12 No.42012 Vol.12 No.32012 Vol.12 No.1/22012 Vol.11 No.42012 Vol.11 No.32012 Vol.11 No.22012 Vol.11 No.12011 Vol.10 No.42011 Vol.10 No.32011 Vol.10 No.1/22011 Vol.9 No.3/42011 Vol.9 No.1/22010 Vol.8 No.3/42010 Vol.8 No.1/22010 Vol.7 No.3/42010 Vol.7 No.1/22009 Vol.6 No.3/42009 Vol.6 No.1/22009 Vol.5 No.42009 Vol.5 No.2/32009 Vol.5 No.12008 Vol.4 No.42008 Vol.4 No.2/32008 Vol.4 No.12008 Vol.3 No.3/42008 Vol.3 No.1/22007 Vol.2 No.3/42007 Vol.2 No.22007 Vol.2 No.12006 Vol.1 No.42006 Vol.1 No.32006 Vol.1 No.22006 Vol.1 No.1

International Journal of Machining and Machinability of Materials (IJMMM)

International Journal of Machining and Machinability of Materials

2018 Vol.20 No.5


Pages Title and author(s)
401-424Optimisation of turning parameters on heat treated INCOLOY 800H using cryogenically treated CVD tool with grey-based entropy method
A. Palanisamy; T. Selvaraj
DOI: 10.1504/IJMMM.2018.096038
425-446Multi response optimisation of machining parameters in EDM of dual particle (MWCNT + B4C) reinforced sintered composites
S. Dhandapani; T. Rajmohanr; D. Vijayan; K. Palanikumar
DOI: 10.1504/IJMMM.2018.096048
447-459Optimisation of machining TI6AL4V alloy: numerical simulation and experimental verification
Alaa H. Jaafar; Haydar Al-Ethari
DOI: 10.1504/IJMMM.2018.096055
460-473Nonlinear modelling of roughness parameters in finish turning of EN31 high carbon steel
Kanishka Jha; Ravinder Kumar; Jagesvar Verma; Ravinder Kataria
DOI: 10.1504/IJMMM.2018.096050
474-495Response optimisation in wire electrical discharge machining of AISI H11 tool steel using Taguchi - GRA approach
M. Vignesh; R. Ramanujam
DOI: 10.1504/IJMMM.2018.096037

 

Return to top