2026 Vol.17 No.32026 Vol.17 No.22026 Vol.17 No.12025 Vol.16 No.42025 Vol.16 No.32025 Vol.16 No.22025 Vol.16 No.1 Free Access2024 Vol.15 No.42024 Vol.15 No.32024 Vol.15 No.22024 Vol.15 No.12023 Vol.14 No.42023 Vol.14 No.32023 Vol.14 No.22023 Vol.14 No.12022 Vol.13 No.42022 Vol.13 No.32022 Vol.13 No.22022 Vol.13 No.12021 Vol.12 No.42021 Vol.12 No.32021 Vol.12 No.22021 Vol.12 No.12020 Vol.11 No.42020 Vol.11 No.32020 Vol.11 No.22020 Vol.11 No.12019 Vol.10 No.42019 Vol.10 No.32019 Vol.10 No.22019 Vol.10 No.12018 Vol.9 No.42018 Vol.9 No.32018 Vol.9 No.22018 Vol.9 No.12017 Vol.8 No.3/42017 Vol.8 No.22017 Vol.8 No.12016 Vol.7 No.3/42016 Vol.7 No.22016 Vol.7 No.12015 Vol.6 No.42015 Vol.6 No.2/32015 Vol.6 No.12014 Vol.5 No.42014 Vol.5 No.32014 Vol.5 No.22014 Vol.5 No.12013 Vol.4 No.3/42013 Vol.4 No.22013 Vol.4 No.12012 Vol.3 No.3/42012 Vol.3 No.22012 Vol.3 No.12011 Vol.2 No.3/42011 Vol.2 No.22011 Vol.2 No.12010 Vol.1 No.3/42009 Vol.1 No.22009 Vol.1 No.1

International Journal of Materials Engineering Innovation (IJMatEI)

International Journal of Materials Engineering Innovation

2020 Vol.11 No.1


Pages Title and author(s)
1-19Analysis of dry sliding wear behaviour of AA-7068/TiC MMCs
Poppathi Naresh; Syed Altaf Hussain; Bandaru Durga Prasad
DOI: 10.1504/IJMATEI.2020.104788
20-33Effect of parameters depth of cut and feed rate on the resistance to pitting corrosion of AISI 1018 steel
Carlos Díaz-Campoverde; Oscar Sotomayor; César Ayabaca; Mario Cesén; Carlos Vila Pastor
DOI: 10.1504/IJMATEI.2020.104789
34-50Investigation on the effect of aluminium foam made of A413 aluminium alloy through stir casting and infiltration techniques
R. Karuppasamy; Debabrata Barik; N.M. Sivaram; Milon Selvam Dennison
DOI: 10.1504/IJMATEI.2020.104790
51-69Effect of hot extrusion on the characteristics of an Mg-3.0Zn-0.7Zr-1.0Cu alloy produced by powder metallurgy
Eacherath Suneesh; Murugesan Sivapragash
DOI: 10.1504/IJMATEI.2020.104791
70-89Statistical modelling and optimisation of the factors affecting the surface roughness of C45 steel treated by the centrifugal disk mass finishing process
K. Djender; K. Hamouda; M. Keddam; M.H.E. Amrou
DOI: 10.1504/IJMATEI.2020.104794

 

Return to top