Journal cover image

Browse issues


Vol. 11
Vol. 10
Vol. 9
Vol. 8
Vol. 7
Vol. 6
Vol. 5
Vol. 4
Vol. 3
Vol. 2
Vol. 1

International Journal of Surface Science and Engineering

2012 Vol. 6 No. 1/2

Special Issue on Characterisation of Surfaces in Materials Processing

Guest Editors: Professor Hong Hocheng and Professor Faruk Yigit

 

Editorial
PagesTitle and authors
3-14Optimal experiment design for plasma thermal spray parameters at bending loads
M. Azadi; A. Moridi; G.H. Farrahi
DOI: 10.1504/IJSURFSE.2012.046837

15-23Microstructure and wear properties of Fe-Cr-C and Fe-Cr-Nb-C clads on carbon steel by TIG surfacing process
Gh. Azimi; M. Shamanian; P. Firozi
DOI: 10.1504/IJSURFSE.2012.046838

24-34The effect of substrate and processing conditions on the properties of sol-gel derived Pb(Zr,Ti)O3 thin films
Ebru Menşur Alkoy; Sedat Alkoy; Tadashi Shiosaki
DOI: 10.1504/IJSURFSE.2012.046839

35-44A new approach for surface state modelling using charge pumping technique in submicron TMOS
Abdelkader Zitouni; Hamid Bentarzi
DOI: 10.1504/IJSURFSE.2012.046840

45-58Selection of advanced coating on a milling cutter used for manufacturing saw teeth
Julfikar Haider; Mohammed Sarwar
DOI: 10.1504/IJSURFSE.2012.046841

59-70Fabricating microstructures on CVD diamond film
Choung-Lii Chao; Wen-Chen Chou; Wen-Chung Lin; Wei-Jhe Su; Kung-Jeng Ma
DOI: 10.1504/IJSURFSE.2012.046842

71-80Microstructure and wear properties of the surface alloyed AZ31 magnesium alloy with aluminium
M. Heydarzadeh Sohi; M.R. Elahi; A. Safaei; J. Rasizadehghani
DOI: 10.1504/IJSURFSE.2012.046843

81-91An analysis of curved tubes finishing by magnetic abrasive finishing
Sh Yousefzadeh; Mehdi Safari
DOI: 10.1504/IJSURFSE.2012.046844

92-100Preparation and characterisation of electrodeposited Ni-Cr/Al2O3 nanocomposite coatings from a trivalent chromium-based bath
R.A. Khosroshahi; M.R. Kiyan Manesh; N. Parvini
DOI: 10.1504/IJSURFSE.2012.046845

101-111Biomachining rates of various metals by Acidithiobacillus thiooxidans
Hong Hocheng; U.U. Jadhav; J.H. Chang
DOI: 10.1504/IJSURFSE.2012.046846

112-121Tool life prediction model of uncoated carbide tool in high speed drilling of Al-Si alloy using response surface methodology
S. Sharif; A. Akhavan Farid; M.H. Idris
DOI: 10.1504/IJSURFSE.2012.046847

122-135Experimental and numerical investigations of temperature measurement of St12 friction stir welded butt joints
Afshin Emamikhah
DOI: 10.1504/IJSURFSE.2012.046848

136-147Numerical and experimental study of residual stress induced by machining process
Ferdinando Salvatore; Faycel Halila; Tarek Mabrouki; Hédi Hamdi
DOI: 10.1504/IJSURFSE.2012.046849

148-156Characterisation of magnesium matrix composite reinforced with SiC particulates manufactured by powder metallurgy method
Sertan Ozan; Lutfiye Feray Guleryuz; Deniz Uzunsoy; Rasim Ipek
DOI: 10.1504/IJSURFSE.2012.046850

157-173Investigation into mechanical properties of high strength steel plates welded with low temperature transformation (LTT) electrodes
Okan Özdemir; Gürel Çam; Hüseyin Çimenoğlu; Mustafa Koçak
DOI: 10.1504/IJSURFSE.2012.046851