Journal cover image

Browse issues

Vol. 57
Vol. 56
Vol. 55
Vol. 54
Vol. 53
Vol. 52
Vol. 51
Vol. 50
Vol. 49
Vol. 48
Vol. 47
Vol. 46
Vol. 45
Vol. 44
Vol. 43
Vol. 42
Vol. 41
Vol. 40
Vol. 39
Vol. 38
Vol. 37
Vol. 36
Vol. 35
Vol. 34
Vol. 33
Vol. 32
Vol. 31
Vol. 30
Vol. 29
Vol. 28
Vol. 27
Vol. 26
Vol. 25
Vol. 24
Vol. 23
Vol. 22
Vol. 21
Vol. 20
Vol. 19
Vol. 18
Vol. 17
Vol. 16
Vol. 15
Vol. 14
Vol. 13
Vol. 12
Vol. 11
Vol. 10
Vol. 9
Vol. 8
Vol. 7
Vol. 6
Vol. 5
Vol. 4
Vol. 3
Vol. 2
Vol. 1

International Journal of Materials and Product Technology

2005 Vol. 24 No. 1/2/3/4

Special Issue on Quenching and Control of Distortion

Guest Editors: Professor Dr. Janez Grum and Professor Dr. George E. Totten


Editorial Part IEditorial Part IIEditorial Part III
PagesTitle and authors
4-52Overview of distortion and residual stress due to quench processing. Part I: factors affecting quench distortion
Lauralice de C.F. Canale, George E. Totten
DOI: 10.1504/IJMPT.2005.007941

53-97Overview of residual stress after quenching. Part II: factors affecting quench residual stresses
Janez Grum
DOI: 10.1504/IJMPT.2005.007942

101-125Oxidation of vegetable oils and its impact on quenching performance
Lauralice de C.F. Canale, Mauro R. Fernandes, Sylvana C.M. Agustinho, George E. Totten, Alessandro F. Farah
DOI: 10.1504/IJMPT.2005.007943

126-141Use of aqueous polymer quenchants for hardening of carbonitrided parts
Wojciech Gestwa, Malgorzata Przylecka, George E. Totten
DOI: 10.1504/IJMPT.2005.007944

142-154Metallurgical behaviours of high-carbon steel wires in lead bath and CMC aqueous solutions by cooling curve analysis
Xinmin Luo, Fang Li
DOI: 10.1504/IJMPT.2005.007945

155-169Computer-aided cooling curve analysis using WinProbe
L. Meekisho, B. Hernandez-Morales, J.S. Tellez-Martinez, X. Chen
DOI: 10.1504/IJMPT.2005.007946

170-183Controllable heat extraction technology - what it is and what it does
Bozidar Liscic
DOI: 10.1504/IJMPT.2005.007947

184-198Determination of heat transfer rates in an industry-like spray quench system using multiple impinging water jets
M.S. Hamed, M. Akmal
DOI: 10.1504/IJMPT.2005.007948

199-206Motivation for the development of new thermal rate sensors for material science applications
J.I. Frankel
DOI: 10.1504/IJMPT.2005.007949

207-223Influence of heating rate, cooling rate and numbers of pulses on the microstructure of AISI 4140 after short-time-hardening
Tatjana Miokovic, Volker Schulze, Detlef Lohe, Otmar Vohringer
DOI: 10.1504/IJMPT.2005.007950

224-240Influence of steel masses and quenchants on mechanical properties of steel
Janez Grum, Slavko Bozic
DOI: 10.1504/IJMPT.2005.007951

244-258Distortion of long cylinders with small diameters due to axial symmetric cooling
F. Frerichs, Th. Luebben, F. Hoffmann, P. Mayr
DOI: 10.1504/IJMPT.2005.007952

259-269Process technology for distortion compensation by means of gas quenching in flexible jet fields
S. Schuettenberg, F. Frerichs, M. Hunkel, U. Fritsching
DOI: 10.1504/IJMPT.2005.007953

270-281Effect of machining and heating parameters on distortion of AISI 52100 steel bearing rings
H. Surm, O. Kessler, F. Hoffmann, P. Mayr
DOI: 10.1504/IJMPT.2005.007954

282-291Surface residual stresses after cooling with and without martensitic transformation of AISI 4140 steel
Janez Grum, Martin Zupancic, Slavko Bozic
DOI: 10.1504/IJMPT.2005.007955

292-305A simple identification of transformation plastic behaviour and some data for heat treating materials
Takayuki Otsuka, Yutaka Wakasu, Tatsuo Inoue
DOI: 10.1504/IJMPT.2005.007956

306-318Mathematical modelling of temperature and stress evolution during cooling of a stainless steel Navy C-ring probe
B. Hernandez-Morales, O. Barba-Mendez, A. Ingalls-Cruz, J.A. Barrera-Godinez
DOI: 10.1504/IJMPT.2005.007957

319-338Experimental investigation and numerical simulation of heat transfer in quenching fluidised beds
W.M. Gao, L.X. Kong, P.D. Hodgson
DOI: 10.1504/IJMPT.2005.007958

339-346Software for computer aided prediction of hardness after hardening of simple components
Janusz Grzyb, Sylwester Jonczyk, Tomasz Babul
DOI: 10.1504/IJMPT.2005.007959

347-360The effect of quench paths on hardness in an infinitely long aluminium cylinder
Xianwu Ling, Harish P. Cherukuri, R.E. Smelser, Paul T. Wang
DOI: 10.1504/IJMPT.2005.007960

361-374Steel superstrengthening phenomenon, part I
N.I. Kobasko
DOI: 10.1504/IJMPT.2005.007961

375-384Heat treatments for obtaining spheroidal cementite in ductile cast iron
L.C. Casteletti, P.E.B. Kinap, P.A.P. Nascente
DOI: 10.1504/IJMPT.2005.007962

385-396Prediction of internal stresses in large-size work pieces during intensive quenching based on temperature–microstructure–stress coupled model
Wei Shi, Zhuang Liu, Kefu Yao
DOI: 10.1504/IJMPT.2005.007963

397-410Quenching in fluidised beds for the heat treatment industry
R. Reynoldson, L.M. Huynh
DOI: 10.1504/IJMPT.2005.007964